Копаем прошивки дальсвязевских модемов

[Boris The Blade]

Сообщение от gemini

Нет, меня это и не интересует особо. Вроде вот эту: http://downloads.openwrt.org/attitud...uashfs-cfe.bin

Пытаюсь собирать прошивку сам, но получается пока плохо:

Лог загрузки

HELO
CPUI
L1CI
DRAM
----
PHYS
PHYE
DINT
LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN


CFE version 1.0.37-106.5 for BCM96328 (32bit,SP,BE)
Build Date: Tue Nov 1 17:30:26 CST 2011 (wanghuaijia@txcpyjeb)
Copyright (C) 2000-2009 Broadcom Corporation.

spi_flash_init
find device_id
spi_flash_get_device_id
device_id =c815
HS Serial flash device: name GD25Q32, id 0xc815 size 4096KB
Total Flash size: 4096K with 1024 sectors
FLASH_BASE = 0xb8000000

fInfo->flash_rootfs_start_offset = 0x00010000

fInfo->flash_meta_start_blk = 1016

fInfo->flash_syslog_start_blk = 0
fInfo->flash_syslog_number_blk = 0
fInfo->flash_syslog_length = 0x0

fInfo->flash_backup_psi_start_blk = 0
fInfo->flash_backup_psi_number_blk = 0

sp startAddr = 0xb83f8000
fInfo->flash_scratch_pad_start_blk = 1016
fInfo->flash_scratch_pad_number_blk = 2
fInfo->flash_scratch_pad_length = 0x2000
fInfo->flash_scratch_pad_blk_offset = 0x0

psi startAddr = b83fa000
fInfo->flash_persistent_start_blk = 1018
fInfo->flash_persistent_number_blk = 6
fInfo->flash_persistent_length = 0x6000
fInfo->flash_persistent_blk_offset = 0x0

Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000

Board IP address : 192.168.1.100:ffffff00
Host IP address : 192.168.1.1
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : openwrt.bin
Boot delay (0-9 seconds) : 1
Board Id (0-4) : 96328A600
Number of MAC Addresses (1-32) : 10
Base MAC Address : 00:10:18:00:00:00
PSI Size (1-64) KBytes : 24
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Main Thread Number [0|1] : 0
User's PSI Size (0-64) KBytes : 0
Voice Board Configuration (0-4) : LE88276

*** Press 'j' or 'J' to stop auto run (1 seconds) ***
Auto run second count down: 110
Booting from only image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x80010000
LZMA: Prossible old LZMA format, trying to decompress..
Decompression OK!
Entry at 0x80010000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80010000
[ 0.000000] Linux version 3.3.8 (jabberd@gemini-desktop) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #2 Sun Sep 22 11:08:57 SAKT 2013
[ 0.000000] Detected Broadcom 0x6328 CPU revision 10b0
[ 0.000000] CPU frequency is 320 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 32 GPIOs
[ 0.000000] gpiochip_add: registered GPIOs 0 to 31 on device: bcm63xx-gpio
[ 0.000000] board_bcm963xx: Boot address 0xb8000000
[ 0.000000] board_bcm963xx: CFE version: 1.0.37-106.5
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: 96328A600
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Memory: 61720k/65536k available (2248k kernel code, 3816k reserved, 408k data, 200k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.048000] NET: Registered protocol family 16
[ 0.276000] registering PCI controller with io_map_base unset
[ 0.288000] bio: create slab <bio-0> at 0
[ 0.292000] PCI host bridge to bus 0000:00
[ 0.296000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x11efffff]
[ 0.300000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.304000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff]
[ 0.308000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
[ 0.312000] pci 0000:00:00.0: PCI bridge to [bus 01-01]
[ 0.316000] pci 0000:00:00.0: bridge window [mem 0x10f00000-0x10ffffff]
[ 0.320000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 0.324000] Switching to clocksource MIPS
[ 0.332000] NET: Registered protocol family 2
[ 0.336000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.344000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.352000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.360000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.368000] TCP reno registered
[ 0.368000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.376000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.384000] NET: Registered protocol family 1
[ 0.388000] audit: initializing netlink socket (disabled)
[ 0.396000] type=2000 audit(0.396:1): initialized
[ 0.400000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.408000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.420000] msgmni has been set to 120
[ 0.424000] io scheduler noop registered
[ 0.428000] io scheduler deadline registered (default)
[ 0.436000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm63xx_uartŠ[ 0.444000] console [ttyS0] enabled, bootconsole disabled
[ 0.444000] console [ttyS0] enabled, bootconsole disabled
[ 0.460000] m25p80 spi0.0: unrecognized JEDEC id c84016
[ 0.500000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.508000] TCP cubic registered
[ 0.512000] NET: Registered protocol family 17
[ 0.516000] 8021q: 802.1Q VLAN Support v1.8
[ 0.524000] VFS: Cannot open root device "mtdblock2" or unknown-block(0,0)
[ 0.528000] Please append a correct "root=" boot option; here are the available partitions:
[ 0.536000] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)

Что вообще делал при сборке

1. Добавил в файл target/linux/brcm63xx/image/Makefile:

# Fujian Star-Net AR800
$(call Image/Build/CFE,$(1),96328A600,6328,AR800)

2. В файл build_dir/linux-brcm63xx/linux-3.3.8/arch/mips/bcm63xx/boards/board_bcm963xx.c:

static struct board_info __initdata board_96328a600 = {
        .name                           = "96328A600",
        .expected_cpu_id                = 0x6328,
 
        .has_uart0                      = 1,
        .has_pci                        = 1,
 
        .has_enetsw                     = 1,

        .enetsw = {
                .used_ports = {
                        [0] = {
                                .used   = 1,
                                .phy_id = 1,
                                .name   = "Port 1",
                        },
                        [1] = {
                                .used   = 1,
                                .phy_id = 2,
                                .name   = "Port 2",
                        },
                        [2] = {
                                .used   = 1,
                                .phy_id = 3,
                                .name   = "Port 3",
                        },
                        [3] = {
                                .used   = 1,
                                .phy_id = 4,
                                .name   = "Port 4",
                        },
                },
        },

};

в этом же файле:

/*
 * all boards
 */
static const struct board_info __initdata *bcm963xx_boards[] = {
#ifdef CONFIG_BCM63XX_CPU_6328
        &board_96328avng,
        &board_96328a600,
        &board_963281TAN,
        &board_dsl_274xb_f1,
#endif

3. И тут: staging_dir/target-mips_uClibc-0.9.33.2/root-brcm63xx/etc/uci-defaults/brcm63xx_fixcrc.sh:

case "$board_name" in
        96328A600 |\
        96328avng |\
        963281TAN |\
        96358-502V |\
        "CPVA502+" |\
        AW4339U |\
        CPVA642 |\
        CT6373-1 |\
        MAGIC |\
        V2110 |\
        V2500V_BB)
                do_fixcrc
                ;;
esac

Чем собираешь OpenWRT - BuildRoot'ом или ImageBuilder'ом?

[gemini]

Сообщение от Boris The Blade

Чем собираешь OpenWRT - BuildRoot'ом или ImageBuilder'ом?

Как-то так:

svn co svn://svn.openwrt.org/openwrt/trunk/
cd trunk
make prereq && make tools/install && make toolchain/install
make defconfig
...
make menuconfig
make

[gemini]

Кстати, из trunk уже что-то получается, но никак не выходит сохранять настройки на флеш-память устройства. Пытаюсь разобраться.

Никакого DSL точно не предвидится, а вот Wi-Fi не получается завести. Но до этого необходимо разобраться с сохранением изменений в файловую систему. Там /dev/mtdblock3 примонтирован в качестве overlayfs, но, похоже, ничего не работает.

Лог загрузки

HELO
CPUI
L1CI
DRAM
----
PHYS
PHYE
DINT
LSYN
USYN
MSYN
LMBE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN


CFE version 1.0.37-106.5 for BCM96328 (32bit,SP,BE)
Build Date: Tue Nov 1 17:30:26 CST 2011 (wanghuaijia@txcpyjeb)
Copyright (C) 2000-2009 Broadcom Corporation.

spi_flash_init
find device_id
spi_flash_get_device_id
device_id =c815
HS Serial flash device: name GD25Q32, id 0xc815 size 4096KB
Total Flash size: 4096K with 1024 sectors
FLASH_BASE = 0xb8000000

fInfo->flash_rootfs_start_offset = 0x00010000

fInfo->flash_meta_start_blk = 1016

fInfo->flash_syslog_start_blk = 0
fInfo->flash_syslog_number_blk = 0
fInfo->flash_syslog_length = 0x0

fInfo->flash_backup_psi_start_blk = 0
fInfo->flash_backup_psi_number_blk = 0

sp startAddr = 0xb83f8000
fInfo->flash_scratch_pad_start_blk = 1016
fInfo->flash_scratch_pad_number_blk = 2
fInfo->flash_scratch_pad_length = 0x2000
fInfo->flash_scratch_pad_blk_offset = 0x0

psi startAddr = b83fa000
fInfo->flash_persistent_start_blk = 1018
fInfo->flash_persistent_number_blk = 6
fInfo->flash_persistent_length = 0x6000
fInfo->flash_persistent_blk_offset = 0x0

Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000

Board IP address : 192.168.1.200:ffffff00
Host IP address : 192.168.1.1
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : openwrt.bin
Boot delay (0-9 seconds) : 1
Board Id (0-4) : 96328A600
Number of MAC Addresses (1-32) : 10
Base MAC Address : 00:10:18:00:00:00
PSI Size (1-64) KBytes : 24
Enable Backup PSI [0|1] : 0
System Log Size (0-256) KBytes : 0
Main Thread Number [0|1] : 0
User's PSI Size (0-64) KBytes : 0
Voice Board Configuration (0-4) : LE88276

*** Press 'j' or 'J' to stop auto run (1 seconds) ***
Auto run second count down: 110
Booting from only image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x80010000
LZMA: Prossible old LZMA format, trying to decompress..
Decompression OK!
Entry at 0x80010000
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x80010000
[ 0.000000] Linux version 3.10.12 (jabberd@gemini-desktop) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38114) ) #6 Sun Sep 22 18:59:31 SAKT 2013
[ 0.000000] Detected Broadcom 0x6328 CPU revision b0
[ 0.000000] CPU frequency is 320 MHz
[ 0.000000] 64MB of RAM installed
[ 0.000000] registering 32 GPIOs
[ 0.000000] board_bcm963xx: Boot address 0xb8000000
[ 0.000000] board_bcm963xx: CFE version: 1.0.37-106.5
[ 0.000000] bcm63xx_nvram: nvram checksum failed, contents may be invalid (expected ffffffff, got e2777034)
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: 96328A600
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
[ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Memory: 61496k/65536k available (2318k kernel code, 4040k reserved, 599k data, 216k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.048000] NET: Registered protocol family 16
[ 0.276000] registering PCI controller with io_map_base unset
[ 0.288000] bio: create slab <bio-0> at 0
[ 0.292000] PCI host bridge to bus 0000:00
[ 0.296000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x11efffff]
[ 0.300000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[ 0.304000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.308000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.312000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff]
[ 0.316000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
[ 0.320000] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 0.324000] pci 0000:00:00.0: bridge window [mem 0x10f00000-0x10ffffff]
[ 0.328000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 0.332000] Switching to clocksource MIPS
[ 0.340000] NET: Registered protocol family 2
[ 0.348000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.352000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.360000] TCP: Hash tables configured (established 512 bind 512)
[ 0.368000] TCP: reno registered
[ 0.372000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.376000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.384000] NET: Registered protocol family 1
[ 0.392000] audit: initializing netlink socket (disabled)
[ 0.396000] type=2000 audit(0.396:1): initialized
[ 0.404000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.408000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.420000] msgmni has been set to 120
[ 0.424000] io scheduler noop registered
[ 0.428000] io scheduler deadline registered (default)
[ 0.436000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm63xx_uart
[ 0.444000] console [ttyS0] enabled, bootconsole disabled
[ 0.444000] console [ttyS0] enabled, bootconsole disabled
[ 0.460000] m25p80 spi1.0: found gd25q32, expected m25p80
[ 0.468000] m25p80 spi1.0: gd25q32 (4096 Kbytes)
[ 0.472000] bcm63xxpart: CFE boot tag found with version 6 and board type 96328A600
[ 0.480000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
[ 0.488000] bcm63xxpart: Partition 1 is kernel offset 10100 and length 10ff00
[ 0.492000] bcm63xxpart: Partition 2 is rootfs offset 120000 and length 2d0000
[ 0.500000] bcm63xxpart: Partition 3 is nvram offset 3f0000 and length 10000
[ 0.508000] bcm63xxpart: Partition 4 is linux offset 10000 and length 3e0000
[ 0.516000] bcm63xxpart: Spare partition is offset 330004 and length bfffc
[ 0.524000] 5 bcm63xxpart partitions found on MTD device spi1.0
[ 0.528000] Creating 5 MTD partitions on "spi1.0":
[ 0.532000] 0x000000000000-0x000000010000 : "CFE"
[ 0.540000] 0x000000010100-0x000000120000 : "kernel"
[ 0.548000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.564000] 0x000000120000-0x0000003f0000 : "rootfs"
[ 0.572000] mtd: partition "rootfs" set to be root filesystem
[ 0.576000] mtd: partition "rootfs_data" created automatically, ofs=0x330000, len=0xc0000
[ 0.584000] 0x000000330000-0x0000003f0000 : "rootfs_data"
[ 0.592000] 0x0000003f0000-0x000000400000 : "nvram"
[ 0.600000] 0x000000010000-0x0000003f0000 : "linux"
[ 0.648000] b53_common: found switch: BCM63xx, rev 0
[ 0.652000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.660000] TCP: cubic registered
[ 0.664000] NET: Registered protocol family 17
[ 0.668000] 8021q: 802.1Q VLAN Support v1.8
[ 0.684000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.696000] Freeing unused kernel memory: 216K (802ea000 - 80320000)
procd: Console is alive
procd: - watchdog -
[ 4.852000] Button Hotplug driver version 0.4.1
kmod: ran 8 iterations
procd: - preinit -
ifconfig: SIOCGIFFLAGS: No such device
Press the [f] key and hit [enter] to enter failsafe mode
mount_root: jffs2 is not ready - marker found
ifconfig: SIOCGIFFLAGS: No such device
procd: - early -
procd: - watchdog -
procd: - init -
Please press Enter to activate this console.
[ 10.000000] NET: Registered protocol family 10
[ 10.896000] wl: module license 'unspecified' taints kernel.
[ 10.904000] Disabling lock debugging due to kernel taint
[ 11.036000] SSB/BCMA glue driver successfully attached
[ 11.044000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[ 11.048000] ------------[ cut here ]------------
[ 11.056000] WARNING: at mm/slab_common.c:377 kmalloc_slab+0x50/0xc4()
[ 11.060000] Modules linked in: wl(P+) wl_glue bcma ipv6 arc4 crypto_blkcipher gpio_keys_polled input_polldev button_hotplug input_core crypto_hash
[ 11.076000] CPU: 0 PID: 249 Comm: kmodloader Tainted: P 3.10.12 #6
[ 11.080000] Stack : 00000006 00000000 00000000 00000000 00000000 00000000 8034b396 00000042
83af1b60 80281c0c 8032b308 802d52db 000000f9 83b7740c b0f00000 00000000
00000001 80029520 00000003 80026eac 00000000 00000000 80283f94 83893984
00893984 00000000 00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000 00000000 83893910
...
[ 11.120000] Call Trace:
[ 11.120000] [<8001ef0c>] show_stack+0x48/0x70
[ 11.124000] [<80027030>] warn_slowpath_common+0x78/0xa8
[ 11.132000] [<80027078>] warn_slowpath_null+0x18/0x24
[ 11.136000] [<800811f0>] kmalloc_slab+0x50/0xc4
[ 11.140000] [<80097468>] __kmalloc+0x20/0x104
[ 11.144000] [<82e2391c>] osl_malloc+0x24/0x6c [wl]
[ 11.152000] [<82e15068>] nvram_init+0x58/0xb0 [wl]
[ 11.160000] [<82e082d0>] si_pci_fixcfg+0x5d4/0xa18 [wl]
[ 11.164000]
[ 11.168000] ---[ end trace 6eb063a36465cbae ]---
[ 11.172000] Got version 2 SPROM from SSB
[ 11.184000] wl0: 5.10.56.27 driver failed with code 13
[ 11.208000] nf_conntrack version 0.5.0 (964 buckets, 3856 max)
[ 11.228000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.260000] Loading modules backported from Linux version master-2013-06-27-0-gdcfa6d5
[ 11.268000] Backport generated by backports.git backports-20130617-4-ge3220f5
[ 11.284000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.356000] xt_time: kernel timezone is -0000
[ 11.404000] cfg80211: Calling CRDA to update world regulatory domain
[ 11.412000] cfg80211: World regulatory domain updated:
[ 11.420000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 11.428000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 11.436000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 11.444000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 11.452000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 11.460000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 11.608000] PPP generic driver version 2.4.2
[ 11.616000] NET: Registered protocol family 24
[ 11.668000] Broadcom 43xx driver loaded [ Features: PNL ]
[ 20.152000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 1, 100Mbps, full-duplex
[ 20.160000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 2, 100Mbps, full-duplex
[ 22.924000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 22.956000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 22.960000] jffs2_build_filesystem(): erasing all blocks after the end marker...
[ 23.988000] jffs2: Newly-erased block contained word 0xdeadc0de at offset 0x00000000
[ 24.024000] done.
[ 24.024000] jffs2: notice: (558) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 24.356000] jffs2: Node CRC ffffffff != calculated CRC f09e7845 for node at 000a0234
[ 24.376000] jffs2: Node CRC ffffffff != calculated CRC f09e7845 for node at 000a02cc
[ 24.400000] jffs2: Node CRC ffffffff != calculated CRC f09e7845 for node at 000a0360
[ 24.424000] jffs2: Node CRC ffffffff != calculated CRC f09e7845 for node at 000a03f4
[ 24.480000] jffs2: Node CRC ffffffff != calculated CRC f09e7845 for node at 000a0480
procd: - init complete -



BusyBox v1.19.4 (2013-09-22 16:39:31 SAKT) built-in shell (ash)
Enter 'help' for a list of built-in commands.

_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (Bleeding Edge, r38114)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme d -----------------------------------------------------
root@OpenWrt:/# uname -a
Linux OpenWrt 3.10.12 #6 Sun Sep 22 18:59:31 SAKT 2013 mips GNU/Linux
root@OpenWrt:/# cat /proc/cpuinfo
system type : bcm63xx/96328A600 (0x6328/0xB0)
machine : Unknown
processor : 0
cpu model : Broadcom BMIPS4350 V7.5
BogoMIPS : 318.46
wait instruction : yes
microsecond timers : yes
tlb_entries : 32
extra interrupt vector : yes
hardware watchpoint : no
isa : mips1 mips2 mips32r1
ASEs implemented :
shadow register sets : 1
kscratch registers : 0
core : 0
VCED exceptions : not available
VCEI exceptions : not available

root@OpenWrt:/# cat /proc/meminfo
MemTotal: 61712 kB
MemFree: 43076 kB
Buffers: 1960 kB
Cached: 6580 kB
SwapCached: 0 kB
Active: 3932 kB
Inactive: 5612 kB
Active(anon): 1052 kB
Inactive(anon): 20 kB
Active(file): 2880 kB
Inactive(file): 5592 kB
Unevictable: 0 kB
Mlocked: 0 kB
SwapTotal: 0 kB
SwapFree: 0 kB
Dirty: 0 kB
Writeback: 0 kB
AnonPages: 1020 kB
Mapped: 1184 kB
Shmem: 68 kB
Slab: 4136 kB
SReclaimable: 676 kB
SUnreclaim: 3460 kB
KernelStack: 232 kB
PageTables: 168 kB
NFS_Unstable: 0 kB
Bounce: 0 kB
WritebackTmp: 0 kB
CommitLimit: 30856 kB
Committed_AS: 3012 kB
VmallocTotal: 1032116 kB
VmallocUsed: 1296 kB
VmallocChunk: 1025588 kB
root@OpenWrt:/# mount
rootfs on / type rootfs (rw)
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,noatime)
sysfs on /sys type sysfs (rw,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
tmpfs on /tmp/root type tmpfs (rw,noatime,mode=755)
tmpfs on /dev type tmpfs (rw,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,relatime,mode=600)
debugfs on /sys/kernel/debug type debugfs (rw,noatime)
/dev/mtdblock3 on /overlay type jffs2 (rw,noatime)
overlayfs:/overlay on / type overlayfs (rw,noatime,lowerdir=/,upperdir=/overlay)
root@OpenWrt:/# df -h
Filesystem Size Used Available Use% Mounted on
rootfs 768.0K 268.0K 500.0K 35% /
/dev/root 2.3M 2.3M 0 100% /rom
tmpfs 30.1M 44.0K 30.1M 0% /tmp
tmpfs 30.1M 24.0K 30.1M 0% /tmp/root
tmpfs 512.0K 0 512.0K 0% /dev
/dev/mtdblock3 768.0K 268.0K 500.0K 35% /overlay
overlayfs:/overlay 768.0K 268.0K 500.0K 35% /
root@OpenWrt:/# ifconfig
eth0 Link encap:Ethernet HWaddr 00:10:18:00:00:00
inet addr:192.168.1.102 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::210:18ff:fe00:0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:14329 errors:0 dropped:14 overruns:0 frame:0
TX packets:76 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1956619 (1.8 MiB) TX bytes:7782 (7.5 KiB)

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:16 errors:0 dropped:0 overruns:0 frame:0
TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:4576 (4.4 KiB) TX bytes:4576 (4.4 KiB)

root@OpenWrt:/# iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

root@OpenWrt:/#

Файлы для модификации в trunk

target/linux/brcm63xx/image/Makefile
build_dir/target-mips_uClibc-0.9.33.2/linux-brcm63xx_generic/linux-3.10.12/arch/mips/bcm63xx/boards/board_bcm963xx.c
staging_dir/target-mips_uClibc-0.9.33.2/root-brcm63xx/etc/uci-defaults/09_fix_crc

[koshkoshka]

Пробовал RT43** выбрать для wifi?

[gemini]

Сообщение от koshkoshka

Пробовал RT43** выбрать для wifi?

Что ты имеешь в виду? Опцию в make menuconfig у openwrt?

[koshkoshka]

Сообщение от gemini

Что ты имеешь в виду? Опцию в make menuconfig у openwrt?

да.

[gemini]

Сообщение от koshkoshka

да.

Пробовал и открытые, и проприетарные дрова Wi-Fi. Никак не завелось. Пока что вернул к старнетовской прошивке и отложил эту затею =)

[MR.MAY]

Подскажите где можно найти прошивку на Ar 800 v1.1 модем черный

[koshkoshka]

Сообщение от MR.MAY

Подскажите где можно найти прошивку на Ar 800 v1.1 модем черный

Сам искал -нигде. Это вообще модем Conexant на самом деле.